Accessories

Quick Connect 3/8" Tube to 3/8" Female Thread.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.

Quick Connect Elbow 1/4" Tube to 1/4" Thread (Male)

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

1/4" (6mm) Tubing Tee with 1/4" Male Thread on Right Side.

Blue retaining clips included but not shown in image.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

• 0 - 999 PPM.
• Battery Powered.
• Handheld and Portable.

Quick Connect Tee 1/4" Tubing Around.

Typically used to "Tee In" to add a pressure gauge or low pressure switch.

3/8" (9.5mm) Tubing to 3/8" Male Thread Straight Connector.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.

1/4" (6mm) Tubing Elbow to 1/4" Spigot.

Spigot's can be pushed into other Quick Connect fittings.

1/4" (6mm) Tubing Elbow to 1/8" Male Thread with One Way Check Valve built in.

Typically used with Reverse Osmosis (RO) systems, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.

Note: Symptoms of faulty check valve could be storage tank not staying full or excess water down the drain line.

It is recommended to use this fitting on the permeate (clean water outlet) line to prevent risk of reverse flow.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.

Quick Connect Y 1/4" (6mm) Tube Around.

Provides the same function as a Tee but in a Y shape.

Quick Connect 1/4" Straight to Female 1/4" Thread.

Typically used with our Pressure Gauges.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Used to power RO Booster pumps and solenoids in domestic RO systems.

*May differ slightly to image due to multiple suppliers, some have connectors and some have only wires.

***The 3AMP and higher ones are switching power supplies in a flatter and longer enclosure, the smaller ones are linear power supplies.

Plastic Ball Valve with 1/4" DCC Fittings.

Used to control flow, also used in reverse osmosis for flushing of membrane.

3/8" (9.5mm) Tubing to 1/4" (6mm) Tubing. Straight Reducer.

Recude 3/8" Tubing to 1/4" Tubing or visa versa.

1/4" Male Thread to 1/4" Male Thread Connector

Also called a Nipple or an RO Nipple.

Commonly used to join 1/4" filter housings.

** Current stock are the top ones with o-rings in the second picture and are made from nylon.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Used in domestic 50GPD or 100GPD reverse osmosis systems.

• Diaphragm Pump.
• Pump and Transformer Included.

Standard female 3/8" Inlet and Outlet.

Voltage: 24V DC
Current: 0.42A, (0.6A Max)
Open Flow: 58LPH (15.3GPH)
Medium: Water
Inlet Pressure: 0.2 MPa (29PSI) Min: 0.05 MPa (7.3PSI) Max: 0.4 MPa (58PSI).
Working Pressure: 0.56MPa (81PSI)
Working Flow: 28LPH (6.9GPH)
Bypass Pressure: 0.70MPa (100PSI) - 0.86MPa (125PSI) MAX
Temperature: 25C

Caution: Motor duty cycle will vary with load and ambient temperature.