Accessories

Fittings, Faucets and other Addons/Accessories.

Sort By:  
10
Spanner to tighten and loosen filter housings.
Needle Valve SS304 with 3/4" Inlets for RO Plant
Add to Cart
R1,391.04
JACO Tee
Plastic Compression Fittings.
RO Membrane Housing Wrench
Used to tighten and loosen RO membrane housings.
10
10" Standard Housing Wrench (HW001)
Housing Wrench / Spanner for our 10" Standard (Basic Blue) Housings.

Used to tighten and loosen filter housing when replacing cartridges.
Spanner to tighten and loosen filter housings.
Needle Valve SS304 3/4" (NVSS34)
Needle Valve SS304 with 3/4" Inlets for RO Plant
Add to Cart
R1,391.04
JACO Tee
Plastic 1/4" Tee (J14-T)

Tee Piece with JACO fittings around.

Plastic Compression Fittings.
50mm Coupler
Pipe Clip 50mm (2inch) Couple (PIPEC5050)
Typically used to couple two RO Linear filters (T33) or similar sized together when adding an extra filter.
Quick Connect Straight 1/4" Tube/Thread (QC-TB-14)

Quick Connect 1/4" Tube to 1/4" Thread (Male).

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Quick Connect T 1/4" Tube/Tube/Thread (QC-T14-T)

1/4" (6mm) Tubing Tee with 1/4" Male Thread on Right Side.

Blue retaining clips included but not shown in image.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Quick Connect Elbow 1/4" Tube/Thread (Female) (QC-TB90-14F14)

Quick Connect 1/4" Elbow to Female 1/4" Thread.

Typically used with our Pressure Gauges.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Quick Connect Elbow 1/4" to 1/8" Thread Check Valve One-Way (QC-TB90-14C)

1/4" (6mm) Tubing Elbow to 1/8" Male Thread with One Way Check Valve built in.

Typically used with Reverse Osmosis (RO) systems, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.

Note: Symptoms of faulty check valve could be storage tank not staying full or excess water down the drain line.

It is recommended to use this fitting on the permeate (clean water outlet) line to prevent risk of reverse flow.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.

Quick Connect 1/4" Tube to 3/8" Thread (QC-T38-14)
Straight 1/4" (6mm) Tube to 3/8" Male Thread

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.
Quick Connect 3/8" Tube to 1/2" Thread (QC-T38-12T)

3/8" (9.5mm) Tubing to 1/2" (12.7mm)  Male Thread

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/2" is 20.8mm.

JACO Elbow
Plastic 1/4" Elbow to 1/4" Thread (J14-EL-14T)

JACK 1/4" Fitting with Elbow to 1/4" Thread (Male)

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Plastic Compression Fittings.
Quick Connect Straight 3/8" Tube/Tube (QC-TT-38)
3/8" (9.5mm) Tubing to 3/8" Tubing Straight Connector, Coupler.

Used to join 3/8" tubing.
RO Membrane Housing Wrench
RO Membrane Housing Wrench (HWM50)
Housing Wrench / Spanner for our 50GPD / 75GPD RO Membrane Housings.

Used to tighten and loosen filter housing when replacing membranes.
Used to tighten and loosen RO membrane housings.
JACO Tee One Leg
Plastic 1/4" T One Leg 1/4" Thread (J14-T-14T)

Tee Piece with JACO fittings on two sides and a standard 1/4" Male thread on one end.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Plastic Compression Fittings.
Quick Connect T 1/4" Tube/Spigot/Tube (QC-T14-S)

Tee 1/4" (6mm) Tubing on side and 1/4" Spigot in middle.

Spigot's can be pushed into other Quick Connect fittings.

Blue retaining clip included but not shown in image.

50mm Coupler
Pipe Clip 60mm (2.5inch) Couple (PIPEC6060)
Typically used to couple two 50GPD/75GPD RO membrane housings or similar sized together.
Quick Connect 3/8" Tube to 3/4" Thread (Female) (QC-TT38-34F)

Quick Connect 3/8" Tube to 3/4" Female Thread.

Typically used on outdoor garden-type taps, typical "hose pipe" size (19mm).

Please Note: The thread fittings are not inner diameter measurements, the inner diameter measurement for 3/4" is 24mm.

Quick Connect Straight 3/8" Tube/Thread (QC-TT38)

3/8" (9.5mm) Tubing to 3/8" Male Thread Straight Connector.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.

Faucet Plastic Tap
Faucet Spout Plastic Tap (FAUP)

For use with under-counter and RO systems.

A hole must be drilled through the counter for mounting.

Note: Flow rate is faster with the elegant faucet.

Per Page      1 - 20 of 94