Search

1/4" (6mm) Tubing Elbow to 1/8" Male Thread.

Typically used with Reverse Osmosis (RO) systems for inlet and waste out, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.

JACO 1/4" with Elbow to 3/8" Thread (Male).

*Image shows 1/4" thread but product is 3/8" thread.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.

Stainless Steel Ball Valve

1/4" Male Thread to 1/4" (6mm) Tubing

Typically used with ball valve adapters when installing point of use filtration systems such as under-counter units and reverse osmosis units.

1/4" Male Thread to 1/4" Male Thread Connector

Also called a Nipple or an RO Nipple.

Commonly used to join 1/4" filter housings.

** Current stock are the top ones with o-rings in the second picture and are made from nylon.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

1/4" (6mm) Tubing Tee with 1/4" Male Thread on Right Side.

Blue retaining clips included but not shown in image.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

1/4" (6mm) Tubing Elbow to 1/8" Male Thread with One Way Check Valve built in.

Typically used with Reverse Osmosis (RO) systems, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.

Note: Symptoms of faulty check valve could be storage tank not staying full or excess water down the drain line.

It is recommended to use this fitting on the permeate (clean water outlet) line to prevent risk of reverse flow.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.

Quick Connect Elbow 1/4" Tube to 1/4" Thread (Male)

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

VENICE Pressure Gauge Glycerine Filled

64mm OD

Pressure shown in kPa.

For reference 100 kPa = 1 BAR.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

3/8" (9.5mm) Tubing Elbow to 1/2" Thread Male.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/2" is 20.8mm.

1/4" (6mm) Tubing Elbow to 3/8" Male Thread.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.

• Can be used vertically or horizontally.
• 1/8" Female Thread.

Suitable for use with Reverse Osmosis Systems, Fish Aquariums, etc

* Requires 1/8" to 1/4" Tubing connector to attach 1/4" tubing, the optional fitting is available.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm and 1/4" is 12.9mm.

Quick Connect 3/8" Tube to 3/4" Female Thread.

Typically used on outdoor garden-type taps, typical "hose pipe" size (19mm).

Please Note: The thread fittings are not inner diameter measurements, the inner diameter measurement for 3/4" is 24mm.

Tee Piece with JACO fittings on two sides and a standard 1/4" Male thread on one end.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.