Reverse Osmosis Spares

RO Spares & Accessories

Sort By:  
G Clamp
Used directly on copper pipe to open water supply for under-counter systems.
Used to electronically open and shut off the flow of water.
Add to Cart
R1,058.00
RO Flow Restrictor and Backwash
Used to restrict flow of RO waste water and backwash membrane.
Empty Post Filter
Can be filled with almost any filter media.
Flow Restrictor 300ML/min
Used to restrict flow on RO waste water.
RO Membrane Housing 50GPD
Housing for 50/75/100/125GPD RO Membranes.
RO Booster Pump for 200GPD RO
24V Working: 70PSI 96LPH for 100-200GPD RO System including switch mode power supply.
Add to Cart
R1,840.00
Leak Detector
Automatically shuts off the water supply if a leak is detected.
Used to shut off RO pump when tank full.
For use with 2 x 200GPD or 1 x 400GPD membrane.
Add to Cart
R1,840.00
RO Booster Pump Gi-An GMB78
24V DC Working: 28LPH 81PSI for 50-100GPD RO System including Transformer.
Add to Cart
R1,664.48
G Clamp
RO Piercing Faucet G Clamp (RO-PFG)

Used directly on copper pipe to attach 1/4" tubing for RO or under counter filtration systems without needing to cut the copper pipe or use additional tools or fittings.

The clamp is secured around the copper pipe and a needle-like fixture pierces the copper pipe to allow the water to flow out the 1/4" adapter where 1/4" tubing is attached.

The faucet can be turned to shut off flow also functioning as a shutoff valve.

Used directly on copper pipe to open water supply for under-counter systems.
24V Solenoid
RO Solenoid 24V DC 1/4" Thread (ROSOL2414)

Used in domestic RO systems.

Solenoid Valve 24V DC Normally Closed.

We have multiple suppliers for these so they may differ to the pictures.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Saddle Clamp
RO Piercing Faucet Saddle Clamp (RO-PFS)

Used directly on copper pipe to attach 1/4" tubing for RO or under counter filtration systems without needing to cut the copper pipe or use additional tools or fittings.

The clamp is secured around the copper pipe and a needle-like fixture pierces the copper pipe to allow the water to flow out the 1/4" adapter where 1/4" tubing is attached.

The faucet can be turned to shut off flow also functioning as a shutoff valve.

Fits both 15mm and 22mm copper pipes.

*actual product may differ slightly to image.

End Cap for 4040 Stainless Steel RO Housing (RO-MH4040SSEC)
RO MEMBRANE HOUSING STAINLESS STEEL PLASTIC END CAP FOR 4040

Cap only which includes 2 rubber seals.

May differ from image due to multiple suppliers.


Replacement End Cap
End Cap for 2540 & 2521 Stainless Steel RO Housing (RO-MH2540SSEC)
RO MEMBRANE HOUSING STAINLESS STEEL PLASTIC END CAP FOR 2540 & 2521.

Cap only.

Stock product image used, may differ to actual item.
Replacement End Cap only
Brass Solenoid 220V AC (ROSOL)
Used with commercial and industrial reverse osmosis systems or custom applications.

  • Body Material: Brass
  • Pressure Max: 12 BAR
  • Input: 220V AC
  • Max Temperature: 80c

*** May differ to image due to multiple suppliers and models.


Used to electronically open and shut off the flow of water.
Add to Cart
R1,058.00
RO Flow Restrictor and Backwash
RO Flow Restrictor 400 with Manual Flush Valve (ROFS400F)
Used to create backpressure on the RO membrane and limit waste water per minute.

Used in under-counter RO systems.
  • 400ML / minute restriction under normal conditions.
  • 1/4" Female fittings.
  • Ball Valve built in for manual flushing.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Used to restrict flow of RO waste water and backwash membrane.
Empty In-Line for Candle
In-Line Housing for Candle Filters (EC-ROC)

Empty In-Line Housing with 1/4" Threads for use with Candle Filter Types.

Uses a rubber o-ring seal.
Can also be used as an empty housing for filter media (such as ion-exchange resin) if you use two sponges.

Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Empty Post Filter
Empty In-Line Housing Post Filter (EC-ROS)

Empty In-Line Housing with 1/4" Female Threads.

Can be filled and refilled with any filter media, mixed bed resin, carbon granules, mineral stones, etc...

Uses a rubber o-ring seal. Includes 2 sponges.

Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.

Can be filled with almost any filter media.
Drain Clamp
Drain Saddle Clamp (DSC)

Used to neatly insert RO 1/4" waste water tubing line into a drain pipe.

Flow Restrictor 300ML/min
RO Flow Restrictor (ROFS)
Used to create backpressure on the RO membrane and limit waste water per minute.

Used in under-counter RO systems.
  • xxxML / minute restriction under normal conditions.
  • 1/4" Female fittings.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Used to restrict flow on RO waste water.
Automatic Shutoff Block for RO
Automatic Shut Off Block for Reverse Osmosis (RO-ASOV)
Available in 1/4" with quick connect and 3/8" with compression nuts (see pictures).

Automatically shuts off the water supply when the tank pressure (or permeate pressure) reaches ~65% of the incoming line pressure.

Without a shut-off block (or solenoid in case of RO with pump) the RO would be wasting water permanently even when the tank is full.
Shuts off water supply when RO tank full.
RO Membrane Housing 50GPD
RO Membrane Housing White (ROMH50)

Reverse Osmosis Membrane Housing.

Fits 50GPD, 75GPD, 100GPD and 125GPD membranes.

Inlet, Permeate and Waste are all 1/8" Female Thread.

We recommend using the one-way check valve on the permeate to prevent reverse flow.

Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.

Housing for 50/75/100/125GPD RO Membranes.
RO Transformer
RO Transformer 24V DC (ROTR24VDC)

Used to power RO Booster pumps and solenoids in domestic RO systems.

*May differ slightly to image due to multiple suppliers, some have connectors and some have only wires.

220V AC to 24V DC
RO Booster Pump for 200GPD RO
RO Booster Pump for 200GPD RO + Transformer (ROBP2)
E-CHEN RO Booster Pump 203 A Series
  • Constant pressure invention design.
  • Extend the life of RO membrane.
  • Solution for water pressure fluctuation problem.
  • Suitable pipe pressure 10-50 psi.
  • No influence from climate and temperature.
  • No decompression.
  • No water leakage problem.
  • Stable current makes transformer's life longer than other booster pump.
  • Constant pressure technology to ensure stable pressure work on RO membrane.

Basic Info

Material:
Cast Iron, EPDM, Santoprene, Nylon
Function: Booster Pump
Performance: No Leak
Flow: 1.6L/M @70psi
Outlet Pressure: Constant @ 70psi
Port: 3/8" FTP
Certificate: Ce, RoHS
Trademark: E-CHEN
Origin: China
Power: Electric
Liquid Media: Water
RO Capacity: 100-200 GPD
Inlet Pressure: 10psi - 50psi
Voltage: 24VDC
Adapter: 3A (Included)
Patent Product: Yes
Specification: 210x104x99mm, 2.2kg
24V Working: 70PSI 96LPH for 100-200GPD RO System including switch mode power supply.
Add to Cart
R1,840.00
Leak Detector
Leak Detector for Under-Counter Systems (ROLEAK)
Shuts off water supply when a leak is detected preventing water damage to cupboards.

This system works with any 10" Single, Dual or Triple Stage Under-Counter Filtration System or RO (Reverse Osmosis) System.

Standard 1/4" Inlet and Outlet.

The leaked-water accumulates in the holding tray and triggers shutoff of the supply.

*Does not include the RO system shown in the image.


Video Demonstration:


Automatically shuts off the water supply if a leak is detected.
High Pressure Switch for RO (RO-PSH)
Used to shut off RO pump when tank full.

  • Normally Closed.

*Note: The optional "1/4" Female Thread (Black) 15A" can be used with two of the 1/4" Thread to 3/8" Tubing Adapters for use with 300GPD and up RO units.
Used to shut off RO pump when tank full.
Booster Pump for 400GPD RO (ROBP400)

High flow booster pump with low energy consumption.

Technical specifications:

  • Electrical connection: DC48V 2.3A
  • Maximum operating pressure: 10.5 Bar
  • Membrane: 2 x 200GPD or 1 x 400GPD
  • Maximum output: 3.0 L/min.
  • Model: HF 45L

*** May differ to images due to multiple suppliers.
For use with 2 x 200GPD or 1 x 400GPD membrane.
Add to Cart
R1,840.00
300GPD Housing
RO Membrane Housing White for 300GPD (ROMH300)

Reverse Osmosis Membrane Housing.

Fits 300GPD membranes.

We recommend using the one-way check valve on the permeate to prevent reverse flow.

*Product may differ slightly to image.

Housing for 300GPD RO Membranes.
RO Booster Pump Gi-An GMB78
RO Booster Pump for 100GPD RO + Transformer (ROBP2)

Used in domestic 50GPD or 100GPD reverse osmosis systems.

  • Diaphragm Pump.
  • Pump and Transformer Included.


Standard female 3/8" Inlet and Outlet.

Voltage: 24V DC
Current: 0.42A, (0.6A Max)
Open Flow: 58LPH (15.3GPH)
Medium: Water
Inlet Pressure: 0.2 MPa (29PSI) Min: 0.05 MPa (7.3PSI) Max: 0.4 MPa (58PSI).
Working Pressure: 0.56MPa (81PSI)
Working Flow: 28LPH (6.9GPH)
Bypass Pressure: 0.70MPa (100PSI) - 0.86MPa (125PSI) MAX
Temperature: 25C

Caution: Motor duty cycle will vary with load and ambient temperature.

24V DC Working: 28LPH 81PSI for 50-100GPD RO System including Transformer.
Add to Cart
R1,664.48
Per Page      1 - 20 of 23