Accessories
Fittings, Faucets and other Addons/Accessories.
Used to tighten and loosen filter housing when replacing cartridges.
- Body Material: Brass
- Pressure Max: 12 BAR
- Input: 220V AC
- Max Temperature: 80c
*** May differ to image due to multiple suppliers and models.
- Displays m3/h.
- 0.4-4 m3/h.
- Has glue-in type 40mm fittings.
- Accuracy +- 5%.
Quick Connect 3/8" Tube to 3/4" Female Thread.
Typically used on outdoor garden-type taps, typical "hose pipe" size (19mm).
Please Note: The thread fittings are not inner diameter measurements, the inner diameter measurement for 3/4" is 24mm.
Applications:
Ozone Injection, fertilizer and chemical injection through drip and sprinkler irrigation systems.
A venturi is a device which creates a vacuum when fluid flows through it. The fluid which creates the vacuum is known as the motive fluid. The motive fluid for irrigation injectors is the irrigation water itself. Vacuum created by the venturi sucks fertilizer or chemical into motive water.
Should not be used in systems where water pressure exceeds 4 BARS.
3/4" Fittings.
Used with countertop diverter valve when tap has no thread.
Used to tighten and loosen filter housing when replacing cartridges.
Used in domestic RO systems.
Solenoid Valve 24V DC Normally Closed.
We have multiple suppliers for these so they may differ to the pictures.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Used to power RO Booster pumps and solenoids in domestic RO systems.
*May differ slightly to image due to multiple suppliers, some have connectors and some have only wires.
***The 3AMP and higher ones are switching power supplies in a flatter and longer enclosure, the smaller ones are linear power supplies.
Tee Piece with JACO fittings on two sides and a standard 1/4" Male thread on one end.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
1/4" (6mm) Tubing Elbow to 1/8" Male Thread with One Way Check Valve built in.
Typically used with Reverse Osmosis (RO) systems, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.
Note: Symptoms of faulty check valve could be storage tank not staying full or excess water down the drain line.
It is recommended to use this fitting on the permeate (clean water outlet) line to prevent risk of reverse flow.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.
Stainless Steel Ball Valve
1/4" Male Thread to 1/4" (6mm) Tubing
Typically used with ball valve adapters when installing point of use filtration systems such as under-counter units and reverse osmosis units.
Used to join 3/8" tubing.
JACO 1/4" to JACO 1/4" Straight connector/coupler.
Used to connect 1/4" tubing.
Quick Connect 3/8" Tube to 3/8" Female Thread.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 3/8" is 16.4mm.
Plastic Pressure Reducing Valve / Pressure Regulating Valve.
- Adjustable.
Typically used in the following POU systems and appliances where water pressure exceeds 4 bars:
- Reverse Osmosis.
- Under-counter filtration units.
- Fridges
- Ice Machines
- Coffee Makers
Default adjustment is around 3.5 bars.
Plastic Ball Valve with 1/4" DCC Fittings.
Used to control flow, also used in reverse osmosis for flushing of membrane.