Accessories
Fittings, Faucets and other Addons/Accessories.
Plastic Ball Valve with 1/4" DCC Fittings.
Used to control flow, also used in reverse osmosis for flushing of membrane.
1/4" Male Thread to 1/4" Male Thread Connector
Also called a Nipple or an RO Nipple.
Commonly used to join 1/4" filter housings.
** Current stock are the top ones with o-rings in the second picture and are made from nylon.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Used to neatly insert RO 1/4" waste water tubing line into a drain pipe.
- Body Material: Brass
- Pressure Max: 12 BAR
- Input: 220V AC
- Max Temperature: 80c
*** May differ to image due to multiple suppliers and models.
1/4" (6mm) Tubing Elbow to 1/8" Male Thread.
Typically used with Reverse Osmosis (RO) systems for inlet and waste out, fits most standard membrane housings.
Blue retaining clip not shown in image but is included.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.
- Normally Closed.
*Note: The optional "1/4" Female Thread (Black) 15A" can be used with two of the 1/4" Thread to 3/8" Tubing Adapters for use with 300GPD and up RO units.
Applications:
Ozone Injection, fertilizer and chemical injection through drip and sprinkler irrigation systems.
A venturi is a device which creates a vacuum when fluid flows through it. The fluid which creates the vacuum is known as the motive fluid. The motive fluid for irrigation injectors is the irrigation water itself. Vacuum created by the venturi sucks fertilizer or chemical into motive water.
Should not be used in systems where water pressure exceeds 4 BARS.
3/4" Fittings.
- Reverse Osmosis
- Water Dispensers (Direct Connect)
- Refrigerators with Water Dispensers
- Aquarium Systems
- Under-Counter Filtration Systems
Sold per meter.
Note: Coloured tubing varies between suppliers, maroon is sometimes supplied as red.
Features & Specifications
- Can be used vertically or horizontally.
- 1/8" Female Thread.
Suitable for use with Reverse Osmosis Systems, Fish Aquariums, etc
* Requires 1/8" to 1/4" Tubing connector to attach 1/4" tubing, the optional fitting is available.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm and 1/4" is 12.9mm.
Used to tighten and loosen filter housing when replacing membranes.
Used in domestic 50GPD or 100GPD reverse osmosis systems.
- Diaphragm Pump.
- Pump and Transformer Included.
Standard female 3/8" Inlet and Outlet.
Voltage: 24V DC
Current: 0.42A, (0.6A Max)
Open Flow: 58LPH (15.3GPH)
Medium: Water
Inlet Pressure: 0.2 MPa (29PSI) Min: 0.05 MPa (7.3PSI) Max: 0.4 MPa (58PSI).
Working Pressure: 0.56MPa (81PSI)
Working Flow: 28LPH (6.9GPH)
Bypass Pressure: 0.70MPa (100PSI) - 0.86MPa (125PSI) MAX
Temperature: 25C
Caution: Motor duty cycle will vary with load and ambient temperature.
Used to tighten and loosen filter housing when replacing cartridges.
This system works with any 10" Single, Dual or Triple Stage Under-Counter Filtration System or RO (Reverse Osmosis) System.
Standard 1/4" Inlet and Outlet.
The leaked-water accumulates in the holding tray and triggers shutoff of the supply.
*Does not include the RO system shown in the image.
Video Demonstration:
Used in domestic 50GPD reverse osmosis systems.
- Diaphragm Pump.
- 3/8" Inlets
Pump only. Transformer not included but optional extra.
Tubing connectors will be required.
Advertised flow rates may vary slightly due to suppliers.
*Pump may differ to image as we have multiple suppliers.