Search
Search Criteria
Products meeting the search criteria
Cap only which includes 2 rubber seals.
Image shown is a 4040 end cap for illustration only.
Bracket for two stage 10" or 20" Big Blue wall mount.
Screw holes may not align with housing screw holes if the housings were not purchased from us, if you are unsure please contact us.
Used to tighten and loosen filter housing when replacing membranes.
Stainless Steel Membrane Housing for Size 4040 Reverse Osmosis Membranes.
Technical information available on request.
Empty In-Line Housing with 1/4" Female Threads.
Can be filled and refilled with any filter media, mixed bed resin, carbon granules, mineral stones, etc...
Uses a rubber o-ring seal. Includes 2 sponges.
Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
20" Filter Housing
Available in Blue & Clear (Transparent)
Pressure reducing valve required if exceeding 4 BAR of pressure or else there will be no warranty.
Max Rating: 6 BAR
Note: Blue housings are "stronger" and can withstand higher pressure.
It is recommended not to install the clear housings outdoors unless they are completely covered due to sunlight aiding bacteria/algae growth.
Housing wrench included.
Reverse Osmosis Membrane Housing with flow restrictor and tubing connectors, pre-assembled.
Fits 50GPD, 75GPD, 100GPD and 125GPD membranes.
As shown in second image.
Reverse Osmosis Membrane Housing.
Fits 50GPD, 75GPD, 100GPD and 125GPD membranes.
Inlet, Permeate and Waste are all 1/8" Female Thread.
We recommend using the one-way check valve on the permeate to prevent reverse flow.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.
May differ from image due to multiple suppliers.
FRP Membrane Housing for Size 4040 Reverse Osmosis Membranes.
Technical information available on request.
Empty In-Line Housing with 1/4" Threads for use with Candle Filter Types.
Uses a rubber o-ring seal.
Can also be used as an empty housing for filter media (such as ion-exchange resin) if you use two sponges.
Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Bracket for three stage 10" or 20" Big Blue wall mount.
Screw holes may not align with housing screw holes if the housings were not purchased from us, if you are unsure please contact us.
Powder Coated (White)
10" Filter Housing
Available in Blue & Clear (Transparent)
If your water pressure exceeds 4 bars you must install a pressure reducing valve, warranty will be void otherwise.
Max Rating 6 BAR.
Note: Blue housings are "stronger" and can withstand higher pressure.
It is recommended not to install the clear housings outdoors unless they are completely covered due to sunlight aiding bacteria/algae growth.
Housing wrench included.
Single bracket for 10" or 20" Big Blue filter housing wall mount.
Screw holes may not align with housing screw holes if the housings were not purchased from us, if you are unsure please contact us.
Bracket for three stage 10" or 20" Big Blue wall mount.
Screw holes may not align with housing screw holes if the housings were not purchased from us, if you are unsure please contact us.
Made from Aluminium.
Used to tighten and loosen filter housing when replacing cartridges.
1/4" Quick Connect fittings on both sides and a 1/4" Female threaded side port.
Side port is used for flushing the membrane.
3 BAR MAX.
Used to tighten and loosen filter housing when replacing cartridges.
Used to tighten and loosen filter housing when replacing cartridges.
Used to tighten and loosen filter housing when replacing cartridges.