Filter Housings
Filter housings are empty housings which require filter cartridges, most housings are used in-line and support a range of standard cartridges.
The 10" standard or slimline housing supports all 10" standard cartridges and the 20" standard or slimline housing supports all 20" standard cartridges. The same goes for the big-blue variants.
Typical maximums are 6 BAR pressure & 50°C. Flow rates depend on the filter inside the cartridge.
Empty In-Line Housing with 1/4" Threads for use with Candle Filter Types.
Uses a rubber o-ring seal.
Can also be used as an empty housing for filter media (such as ion-exchange resin) if you use two sponges.
Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
Reverse Osmosis Membrane Housing with flow restrictor and tubing connectors, pre-assembled.
Fits 50GPD, 75GPD, 100GPD and 125GPD membranes.
As shown in second image.
If your water pressure exceeds 4 bars you must install a pressure reducing valve, warranty will be void otherwise.
Max Rating 6 BAR.
Fits 10" BigBlue Cartridges.
Housing wrench included,
Notice: Please be advise new stock the housings are black no longer blue.
Empty In-Line Housing with 1/4" Female Threads.
Can be filled and refilled with any filter media, mixed bed resin, carbon granules, mineral stones, etc...
Uses a rubber o-ring seal. Includes 2 sponges.
Not recommended where pressure may exceed 4 bars without using a pressure reducing valve.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/4" is 12.9mm.
FRP Membrane Housing for Size 4040 Reverse Osmosis Membranes.
Technical information available on request.
10" Filter Housing
Available in Blue & Clear (Transparent)
If your water pressure exceeds 4 bars you must install a pressure reducing valve, warranty will be void otherwise.
Max Rating 6 BAR.
Note: Blue housings are "stronger" and can withstand higher pressure.
It is recommended not to install the clear housings outdoors unless they are completely covered due to sunlight aiding bacteria/algae growth.
Housing wrench included.
If your water pressure exceeds 4 bars you must install a pressure reducing valve, warranty will be void otherwise.
Max Rating 6 BAR.
Fits 20" BigBlue Cartridges.
Housing wrench included.
20" Filter Housing
Available in Blue & Clear (Transparent)
Pressure reducing valve required if exceeding 4 BAR of pressure or else there will be no warranty.
Max Rating: 6 BAR
Note: Blue housings are "stronger" and can withstand higher pressure.
It is recommended not to install the clear housings outdoors unless they are completely covered due to sunlight aiding bacteria/algae growth.
Housing wrench included.
Reverse Osmosis Membrane Housing.
Fits 50GPD, 75GPD, 100GPD and 125GPD membranes.
Inlet, Permeate and Waste are all 1/8" Female Thread.
We recommend using the one-way check valve on the permeate to prevent reverse flow.
Please Note: The thread fittings are not outer diameter measurements, the outer diameter measurement for 1/8" is 9.9mm.
Stainless Steel Membrane Housing for Size 4040 Reverse Osmosis Membranes.
Technical information available on request.
- Available in White, Blue & Clear (Transparent, may have a purplish hue).
- Clear housings may promote growth of bacteria and algae.
- Clear housings should not be installed where they might get direct sunlight.
If you suspect that your pressure at any time may exceed 4 Bars we recommend installing a pressure reducing valve, we will not replace damaged housings where operating pressure has been exceeded.
Max Rating: 6 BAR
Housing wrench sold separately!
White and Clear Housings are only available in 1/4" and 3/8".
Blue Housings are only available in 1/2" and 3/4".
Reverse Osmosis Membrane Housing.
Fits 300GPD membranes.
We recommend using the one-way check valve on the permeate to prevent reverse flow.
*Product may differ slightly to image.
- 1